WISA 300VP High Security Inwall Cistern
The Wisa WS300VP high security inwall cistern is ideal for use in public places where reliability is important and where mains pressure flush valves are not practical due to insufficient pipe sizing.
The cistern is supplied with a robust stainless steel push button assembly which is screw fixed to the wall, a pneumatic actuator and pneumatic tubing allowing flexibility of button mounting point.
The inwall cistern is supplied as standard in a 6L capacity and is only available as a single full flush. Full duct access must be available to the WS300VP for servicing purposes.
Zurn Sensor Flush Valve
Zurn Model ZEM-6152XL flush valve is a sensor activated WC flushing valve with an approved vacuum breaker allowing direct connection to potable water supply without any additional backflow protection. The standard valve is pre-set to deliver a 6L flush and has achieved the distinction of Australian Standards Watermark approval and WELS 1 Star rating. Valve upgradable to 4.5L flushing should regulations permit.
Zurn Mop And Broom Holder Rack
Zurn Z-MH mop and broom holder rack is fabricated of one-piece hi-hat channel Type 304 stainless steel, 20 gauge, with satin finish. Each mop holder is on a pivoting spring loaded serrated rubber that can hold the round handles of 22-32mm diameter wedged against the ribbed clamp plate. The Z-MH comes in three different lengths; 660mm for 3 mops; 914mm for 4 mops; and 1168mm for 5 mops.
Zurn Sink Faucet For Cleaners Sink
Zurn Z-SF is a purpose made commercial grade wall mounted faucet suitable for use above cleaners sinks.
It is polished chrome plated cast brass with 1/4 turn ceramic disc cartridges, with eccentric swivel inlets allowing adjustable centres from 184mm to 222mm. Inlets include integral isolators allowing inline servicing. Valve spout includes chemical resistant vacuum breaker for backflow protection and 3/4" hose connection allowing use of Zurn Z-HH short hose. Valve has adjustable wall brace and bucket hook allowing buckets to be hung off faucets while filling.
Zurn Floor Mounted Mop Sink
Zurn Z-1996 mop service basin is made of a molded high density composite, designed for commercial applications for use in back-osff-house applications, and includes a PVC drain body, stainless steel strainer and 3" gasketed outlet connection.
Options available to add to your cleaners sink are as shown below and can be seen under MODELS:
KWC Stainless Steel Cleaners Sink
KWC FRCS is a wall mounted, one-piece pressed Type 304 stainless steel cleaners sink. Available with or without a back-splash and with or without a bucket grid. Measurements are 600 x 500 x 344mm (WDH including brackets).
KWC high quality cleaners sinks are ideally suited for installation in industrial workshops, sports facilities, school bathrooms, hospitals, care facilities and early childhood education facilities.
These sinks are best fitted with our Zurn Z-SF sink faucet (see separate data sheet) which comes with an integrated vacuum break and bucket hook on the spout.
KWC Stainless Steel Accessible Compliant Toilet Suite
The KWC FRFM5-300VP is a disabled compliant stainless steel back to wall/ floor mounted toilet suite. It is suitable when vandal resistant products are required.
The FRFM5 toilet suite is available with either cistern or flush valve options, depending on foot traffic.
KWC Accessible Compliant Stainless Steel Wall Mounted Toilet Pan
Wall mounted disabled compliant toilet pan, fabricated in 1.6mm Type 304 stainless steel with a satin finish. Built for areas where vandalism is likely to cause damage to ceramic toilet's. It is designed for face wall or through wall mounting where structural wall is capable of supporting required load. They are 3 Star WELS rated when installed with a similarly rated flushing device.
KWC Stainless Steel Accessible Floor Mounted Toilet Pan
KWC Accessible Compliant floor mounted WC pan for disabled, hidden mounting with stainless steel rods through wall, fixing and service via maintenance room or side access panels, type 304 stainless steel, surface satin finished, material thickness 1,5 mm, concealed flushing rim with min. 6 liter flushing capacity, with a shrouded 100 mm diameter horiziontal 'P' trap outlet, pressed seat area tapered towards centre, all edges curved, fixing with 280 mm stainless steel rods and screw nuts (included) through the wall.
Dimensions 360 x 450 x 700 mm (W x H x L)
Franke Stainless Steel Medium Duty Security Wash Basin
The Franke ANMX452 is a satin finish Type 304 stainless steel basin.
The ANMX452 has a deep bowl with a 32mm waste. Trap is not supplied. Basin is not pre-punched for taps but can be on special request.
The basin is designed to be face wall mounted with a removable shroud allowing access to fixing and waste and water fittings. The shroud is securely fastened to the basin and wall using a concealed Allen screw fixing.
It is suitable for use in vandal prone areas such as public toilets, schools, courthouses, prisons, and police stations.
